4W point light with three transparent polycarbonate caps (10mm and 24mm). The module is delivered completely wired-up on an aluminum retaining plate for cooling and mounting. Another small heatsink for an alternative mounting with smallest dimensions is included.

You only have to glue on the desired cap and heatsink with superglue. The 10mm cap serves as light distribution concerning the concealed installation behind a fiberglass wall. The 24mm cap can be used for external installation for it completely covers the module. The accessory includes a profile expansion, which can be optionally glued on the 10mm cap.

Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. Continuous operation with the provided cooling elements is possible when paying attention to a slight air flow. Please check operation temperatures after installation.

Technical Data

Electricity: 4W reference power, 8(12)V, 0.35A
Beam angle: ~160°
Light intensity: ~50 Lumen RED
Light intensity: ~70 Lumen GREEN
Light intensity: ~100 Lumen WHITE
Dimension base plate: 10x50mm
Dimension additional heatsink: 15x15x6mm, self-adhesive
Small cap: D10x12mm + profile expansion
Big cap: D24x10mm
Weight: 6g (without cable)
Delivery: ready to use with 1m / 3ft connection cable and series resistor for 2S, resistor for 3S enclosed

High power light with two 8Wx2 reference power and wide radiation angle. The lights are controlled separately and can be used as rotating beacon or parallel as ultra high power strobe. The light is delivered with several radiation caps for individual usage:

1x 24mm ROUND
1x 24mm PROFILE

The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use two 8W-3S adapter cables.

Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These 8W luminaires are not suitable for continuous operation without additional cooling, operation times of a few minutes are possible. Please check operation temperatures. The luminaires are perfectly suited to be BEACON or ACL lights. The integrated temperature sensor will switch off the light in case of overheating.

Technical Data

Electricity: 8W reference power, 8(12)V, 2x0.7A
Beam angle: >160°
Light intensity: 2x~200 Lumen RED
Light intensity: 2x~400 Lumen WHITE
Dimension: 24x20x20mm
Weight: 6g (without cable)
Delivery: ready to use with 1m / 3ft silicon cable and series resistor for 2S, resistor for 3S enclosed

Miniatur stick light with very good performance. Smallest diameter and transparent 7mm polycarbonate cap. Great for thin wing tips and rudder.

Technical Data

Electricity: 2Wx2W reference power, 8(12)V, 0.17A
Beam angle: >150°
Light intensity: ~50 Lumen Red (RD)

Light intensity: ~80 Lumen Green (GN)

Light intensity: ~110 Lumen White (WE)
Dimensions: D7x37mm
Delivery: ready to use with 0.5m / 1.5ft cable, and ready made series resistor for 2S. Resistor for 3S enclosed

Powerful flashlight light in x2-Technology - doubled luminous power but the same waste heat! The profile light of the 11mm series is slim outside and fits optically also onto smaller models. Because of the x2-Technology, the light has an enormous luminous power and thus it's an eye-catcher even for bigger models.
In delivery state, the profiled polycarbonate cap is simply attached. It can be varnished separately. It's highly transparent. The cap must be glued after the final assembly.
Additional cooling surfaces have been waived in order to enable an extremely flat and compact assembly, especially on fuselages or wingtips.
Hence, this luminaire is exclusively suitable for flash mode or short blink operation. In order to ensure operational reliability of luminaire and model, an temperature protection is built in. If the luminaire is operated for too long and thus becoming too hot, this button switches off the light. In order to increase the life span, do not use this function permanently!
The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use a 4W-3S adapter cable.

Technical Data

Electricity: 8Wx2 reference power, 8(12)V, 0.7A
Beam angle: >160°
Light intensity: 2x80 Lumen RED (RT)
Light intensity: 2x200 Lumen WHITE (WE)
Dimension light cap: 11.5x42.5x10mm, may be lowered up to 4mm without loss of beam angle
Total mass: 11.5x42.5x10mm
Weight: 5g (without cable)
Delivery: ready to use with 1m / 3ft silicon cable and series resistor for 2S, resisitor for 3S enclosed

Powerful Position-/Navigation Light in x2-Technology - doubled luminous power but the same waste heat! The profile light of the 11mm series is slim outside and fits optically also onto smaller models. Because of the x2-Technology, the light has an enormous luminous power and thus it's an eye-catcher even for bigger models. The innovative, internally positioned cooling surface enables astonishingly compact dimensions with an unique slim design.
In delivery state, the profiled polycarbonate cap is simply attached. It can be varnished separately. It's highly transparent.
The assembly of the lamp is astonishingly easy: With a simple surface mount, all you need is a slot of 5x33mm. This way, the luminaire can be also mounted on smaller wing tips or fuselages. If desired, you can recess the luminaire up to 4mm, thus achieving an even smaller construction. The cap must be glued after the final assembly.
The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use a 4W-3S adapter cable. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heat sink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation.

Technical Data

Electricity: 8Wx2 reference power, 8(12)V, 0.7A
Beam angle: >160°
Light intensity: 80x2 Lumen RED (RT)
Light intensity: 140x2 Lumen GREEN (GN)
Light intensity: 200x2 Lumen WHITE (WE)
Dimension assembly pin: 33x5*60
Dimension light cap: 11.5x42.5x10mm, may be lowered up to 4mm without loss of beam angle
Outside dimensions: 11.5x42.5x70mm
Weight: 13g (without cable)
Delivery: ready to use with 1m / 3ft silicon cable and series resistor for 2S, resistor for 3S enclosed.

Profiled high-performance spotlight with 4W and very good beam angle through a special spreading cap. The luminaire is delivered as a ready assembled unit on an aluminum assembly plate and a changeable polycarbonate cap as covering. The luminaire is ready to use for 2S Lipo (ca. 8V) operation. With 3S (12V) operation, the enclosed resistor has to be used. Alternatively use a 4W-3S adapter cable.
Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with assembly of cooling elements are suitable for continuous operation if air convection is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation.

Technical Data:

Electricity: 4W reference power, 8(12)V, 0.35A
Beam angle: >160°
Light intensity: ~50 Lumen RED
Light intensity: ~70 Lumen RED
Light intensity: ~100 Lumen WHITE
Dimension base panel: 16x37mm
Overall dimension: 17x38x9mm
Weight: 4g (without cable)
Delivery: ready to use with 1m connection cable and series resistor for 2S, resistor for 3S enclosed.

The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.
Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

Items other than the 4W Position-/Navigation Light 16mm not included.
Note: The LED lights are extremely bright! Never look directly into a LED!

A white 4W flashlight and a 4W position light combined in the small 24mm profile housing with integrated cooling surfaces. Both lights are individually controlled and thus ideally suited for the combined operation as position and flashlight.
The luminaire is delivered as a ready assembled unit on an aluminium cooling plate and a changeable polycarbonate cap as covering. The luminaire is ready to use for 2S Lipo (ca. 8V) operation. With 3S (12V), the enclosed resistor has to be used. Alternatively use a 4W-3S adapter cable.
Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These luminaires with assembly of cooling elemets are suitable for the combined operation as position and flashlight, i.e. the position light glows longer, the white luminaire solely blinks/flashes. Make sure that air convection is possible. Please check operation temperatures after installation.

Technical Data

Electricity: 8W(2*4W) reference power, 8(12)V, 2*0.35A
Beam angle: >160°
Dimension base panel: 24x56x9mm
Dimension light cap: 24x43x9mm
Luminous flux: ~50 Lumen RED
Luminous flux: ~70 Lumen GREEN
Luminous flux: ~100 Lumen WHITE
Thickness assembly plate: 2mm
Weight: 11g (without cable)
Delivery: ready to use with 2*1m connection cable and series resistor for 2S, resistors for 3S enclosed 

Profiled high-performance spotlight with 4W and very good beam angle through a special spreading cap. The luminaire is delivered as a ready assembled unit on an aluminum assembly plate and a changeable polycarbonate cap as covering. The luminaire is ready to use for 2S Lipo (ca. 8V) operation. With 3S (12V) operation, the enclosed resistor has to be used. Alternatively use a 4W-3S adapter cable.
Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with assembly of cooling elements are suitable for continuous operation if air convection is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation.

Technical Data:

Electricity: 4W reference power, 8(12)V, 0.35A
Beam angle: >160°
Light intensity: ~50 Lumen RED
Light intensity: ~70 Lumen RED
Light intensity: ~100 Lumen WHITE
Dimension base panel: 24x43x9mm
Thickness of assembly plate: 2mm
Weight: 8g (without cable)
Delivery: ready to use with 1m connection cable and series resistor for 2S, resistor for 3S enclosed

The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

Items other than the 4W Position-/Navigation Light 24mm not included.
Note: The LED lights are extremely bright! Never look directly into a LED!